Teradek User Guide

RED Camera Control

Updated on

RED cameras support control via the RED Control app and other third party applications. They can also be controlled by a SmallHD monitor with a RED camera control license. Bolt 7 can be used with your camera to facilitate long range wireless camera control over its built-in data radio. Depending on the camera, Bolt 7 acts as either a network or USB bridge between the camera and control interfaces.

Bolt 7 Setup

The first thing you'll need to know when setting up Bolt 7 with your RED camera is whether Bolt 7 is going to be directly connecting the camera to a control interface like a SmallHD monitor, or if the camera is connecting to an existing network.

All of the settings for enabling camera control via Bolt can be found in the Data Settings menu. You can read more about all the available Data Settings in the Configuration guide: Data Settings

After pairing, the only setting you need to worry about is Bolt 7's Net Mode.


Bolt 7 TXBolt 7 RX
Net Mode
  • Standalone - Use this with a network connection when Bolt 7 is connecting the camera directly to the controller
  • Client - Used when connecting the camera and controller with other network equipment
  • USB Serial - For use with the camera's 9 pin EXT port
  • Client - For network connections
  • USB Serial - For use with the camera's 9 pin EXT port

If you're using a direct connection with no other network equipment, Bolt 7 TX's Net Mode should be set to Standalone. In Standalone mode, Bolt 7 TX acts as the network router, and can assign network IP addresses to the camera and a monitor or computer connected to the RX.

If there is an existing network you want to use, set the TX net mode to Client. Client mode means that Bolt will only act as a network passthrough, and will not try to manage the network.

In both cases, the RX's Net Mode setting should be Client.

When using cameras like KOMODO or V-RAPTOR's 9 pin EXT port, use the USB serial setting to enable a USB bridge between Bolt 7 TX and RX .

Camera Setup

Sony camera network settings vary slightly between cameras, and some cameras support an Ethernet connection, Ethernet via USB-C (Tethering), or direct USB PTP connection. For FX6, and BURANO, most of the camera configuration lives in the Network > Wired LAN settings. Refer to your camera's manual for details on the supported connectivity types.

If you are adding Bolt 7 to an existing camera control workflow with other network equipment and both TX and RX in standalone mode, you should not need to change any of the network settings on your camera or control app.

When using Bolt 7 directly between the camera and control app in Standalone mode, you will need to check the network settings of the camera. If the camera is in DHCP mode, you'll need to note the camera's IP address, which can be found under the Network > Wired LAN > IP Address screen. This IP address is given out by Bolt 7. 

Enter this IP address when configuring the control app or SmallHD monitor.

Camera Step-by-step

Setup will vary slightly between cameras and the available ports

Connect to your camera via Ethernet, USB-C, or the EXT port

  • Ethernet: Connect RED's 9 pin to RJ45 cable to Bolt using a SmallHD 5-pin to RJ45 adapter.
  • USB-C: Connect USB-C from the camera to Bolt 7's USB-C port. NOTE: Ensure that DP-Alt input mode is disabled in the TX Video Settings menu
  • EXT Port: Connect a 9 PIN EXT to 5-Pin USB between the camera and Bolt 7 TX. Connect a USB-C to 5-pin cable between the Bolt RX and SmallHD monitor.

Configure the camera

  • Ethernet Connection
    1. Open the camera's full menu
    2. Navigate to Network > Wired LAN
    3. Ensure that Wired LAN is set to ON
    4. Ensure that Camera Remote Control is set to Enable
  • USB-C Connection
    1. Open the camera's full menu
    2. Navigate to Network > USB Tethering
    3. Ensure USB Tethering is set to ON
    4. Ensure Camera Remote Control is set to Enable
    5. Refer back to the Network > Wired LAN menu to view the camera's network information
  • EXT port connection
    1. Open the Camera menu and navigate to Communication > Connections
    2. Select Serial
    3. Set the Protocol to Network (PPP), Baud rate should be 115200, and the IP address can be left at the default (169.254.1.1)
  • Refer to the camera's manual for additional network configuration info
  • Configure the Camera's Remote control password on the Network > Network Setup menu. You will need the password in order to connect

SmallHD Monitor Setup

Before configuring camera control on your SmallHD monitor, you'll need to connect Bolt 7 to the monitor.

For network control via Ethernet or USB-C, connect to the monitor with either a 5-pin to USB-C cable, or 5-pin to Ethernet adapter.

If you chose the EXT port connection (see above), use a 5-pin to USB-C cable, Ethernet will not work. Note that a 5-pin to 5-pin USB cable cannot be used between Bolt 7 and the monitor as both ports operate in USB host mode.

 After connecting the cable between Bolt 7 and the monitor you can configure the Camera Control function in the monitor.

  1. Open the monitor's settings menu
  2. Scroll down to Camera control
  3. Select the appropriate RED camera control. If you don't see this menu option, you may need to purchase a camera control license. Please visit www.smallhd.com to purchase the license
  4. Select Network or Serial control depending on how you connected your camera above

SmallHD has more info about Camera control in their reference guide: https://guide.smallhd.com/m/118985/c/418183

Supported Cameras

  • Protocol: RCP2
    • KOMODO
    • KOMODO-X
    • V-RAPTOR
    • V-RAPTOR XL
  • Protocol: DSMC2
    • EPIC-W
    • SCARLET-W
    • DRAGON
    • GEMINI
    • MONSTRO

Additional Notes

  • Ensure the camera and monitor are on the same subnet if using Client mode with another router.
  • Some network settings may vary slightly by firmware version—always refer to the latest camera manuals for exact menu locations.

For additional guidance, see RED's official documentation: RED KOMODO / V-RAPTOR DSMC3 Wi-Fi & Network Setup Manual

Previous Articles Sony Camera Control
Next Articles Frequencies
Still Need Help? Contact Us