Bolt 7 contains several wireless configuration options that allow the system to work at its best in different environments. The system is designed to work adequately using its default, automatic settings, but they may not be ideal for all situations. This section details all available wireless configuration options for the transmitter and receiver.
Wireless Settings
Band/Frequencies
Use the Band/Frequencies menu to select the wireless band and operating frequencies.
The Band menu (right panel) lets you select either 5GHz or 6GHz frequency bands. 5GHz allows for higher total output power, but is more likely to experience interference from other wireless devices (Wi-Fi routers, cell phones, IoT devices, and other wireless video systems), resulting in interference and video dropouts. The 6GHz (U-NII-5) band is less congested compared to the 5GHz band, and although the allowed output power is lower, it should offer better connection stability with fewer interruptions. 6GHz can be used in mostregions. For a complete list of available frequencies, refer to the Frequencies By Region chart.
The Frequencies menu (left panel) contains a list of all available frequencies. Bolt 7 will automatically select an operating frequency when multiple values are selected. If both the transmitter and receiver have Fixed Frequency Mode enabled, you can only select one frequency for Bolt 7 to use. Frequencies marked with (DFS) must be scanned for one minute before they can be used, but are typically less crowded. For all available frequencies, refer to the Frequencies By Region chart.
Bandwidth
The Bandwidth menu lets you choose between 40MHz (default) and 20MHz operating modes. Ensure that both the transmitter and receiver are set to the same bandwidth with a resolution of up to 1080p60. For all available frequencies, refer to the Frequencies By Region chart.
- 20MHz - Uses half the bandwidth of 40MHz, allowing more systems to operate simultaneously with less chance of interference. This mode reduces maximum video quality and is recommended for HD transmission only.
- 40MHz - (Default) Offers the best video quality and most robust transmission, but provides fewer available channels and is more susceptible to interference.
NOTE: 20MHz mode supports HD/3G resolutions up to 1080p60. Resolutions up to 4k30 are also supported but downscaled to 1080p before transmission (4k50/59/60 is not supported).
Video Quality (TX only)
The Video Quality menu lets you adjust the balance between your signal’s maximum range and quality according to the number of antennas used to transmit fine information. Bolt 7 has three picture quality levels that vary based on the lowest quality link or the furthest receiver.
- Auto Mode - (Default) Transmitter automatically determines how many fine antennas are needed based on the range and signal quality.
- Longer Distance Mode - Maintains the maximum range in situations where other sources of interference might be present, but will slightly reduce your video signal’s maximum quality.
- Better Quality Mode - Maintains higher signal quality but reduces the maximum range.
- Best Quality Mode - Ideal for complex, high-contrast scenes that require the highest possible quality.
- Low Power Mode - Reduces the transmitter's total power.
Fixed Frequency
Fixed Frequency Mode bypasses any automatic frequency switching logic, allowing your Bolt 7 system to always attempt to connect on a specified frequency. Once a frequency is selected, the transmitter will only use that frequency. This allows the transmitter to link/reconnect to the receiver much faster. After enabling Fixed Frequency mode, navigate to Frequencies and select a frequency within the selected wireless region (non-DFS frequencies only). There are two options for Fixed Frequency Mode:
- Non-DFS and non-6GHz channels
- Specific non-DFS 5GHz channels
For best results, ensure that both the transmitter and receiver have Fixed Frequency Mode enabled, and use the Spectrum Analyzer (on the receiver's front panel or the Bolt app) to search for the least congested frequency to use.
- Fixed Frequency Mode Disabled - Bolt 7 scans all available frequencies and repeatedly switches from one frequency to the next during transmission.
- Fixed Frequency Mode Enabled - Bolt 7 connects to one specific frequency.
NOTE: By default, Bolt 7 will select the lowest available frequency from the Frequencies list if one has not been selected beforehand.
Enable Broadcast Mode (Bolt 7 MAX only)
Enabling Broadcast Mode improves the system's maximum transmission range by allowing Bolt MAX systems to operate without any back-channel communication between the receiver and transmitter, and reduces any interference.
- Broadcast Mode Disabled (Standard Multicast Mode) - Transmitter and connected receiver(s) coordinate and maintain two-way communication with each other to optimize frequency usage and video transmission.
- Broadcast Mode Enabled - This allows the transmitter to connect to an unlimited number of receivers, as long as they have already been paired. To achieve even better range performance, attach the receiver to your Bolt Panel Antenna while in Broadcast Mode.
NOTE: Bolt 7 XT/LT 750 and 1500 receivers will not link to a Bolt 7 XT/LT MAX transmitter in Broadcast Mode, even if they were previously paired. You must use a Bolt 7 MAX receiver. Otherwise, the receiver's OLED will display Broadcast Not Supported


