SONY cameras support Ethernet control via SONY's Monitor & Control App and other third party applications. They can also be controlled by a SmallHD monitor with a SONYcamera control license. Bolt 7 can be used with your camera to facilitate long range wireless camera control over its built-in data radio without any disruption to any existing camera control workflow. Most of the camera control workflows are network-based, so Bolt 7 will be acting as a network bridge between the camera and control interfaces.
Bolt 7 Setup
The first thing you'll need to know when setting up Bolt 7 with your Sony camera is whether Bolt 7 is going to be directly connecting the camera to a control interface like a SmallHD monitor, or if the camera is connecting to an existing network.
To start, you'll need a paired Bolt 7 TX and RX. All of the settings to enable camera control can be found in the Data Settings menu. You can read more about all the available Data Settings in the Configuration guide: Data Settings
After pairing, the only setting you need to worry about is Bolt 7's Net Mode.
| Bolt 7 TX | Bolt 7 RX | |
|---|---|---|
| Net Mode |
|
|
If you're using a direct connection with no other network equipment, Bolt 7 TX's Net Mode should be set to Standalone. In Standalone mode, Bolt 7 TX acts as the network router, and can assign network IP addresses to the camera and a monitor or computer connected to the RX.
If there is an existing network you want to use, set the TX net mode to Client. Client mode means that Bolt will only act as a network passthrough, and will not try to manage the network.
In both cases, the RX's Net Mode setting should be Client.
Camera Setup
Sony camera network settings vary slightly between cameras, and some cameras support an Ethernet connection, Ethernet via USB-C (Tethering), or direct USB PTP connection. For FX6, and BURANO, most of the camera configuration lives in the Network > Wired LAN settings. Refer to your camera's manual for details on the supported connectivity types.
If you are adding Bolt 7 to an existing camera control workflow with other network equipment and both TX and RX in standalone mode, you should not need to change any of the network settings on your camera or control app.
When using Bolt 7 directly between the camera and control app in Standalone mode, you will need to check the network settings of the camera. If the camera is in DHCP mode, you'll need to note the camera's IP address, which can be found under the Network > Wired LAN > IP Address screen. This IP address is given out by Bolt 7.
Enter this IP address when configuring the control app or SmallHD monitor.
Camera Step-by-step
The following instructions were created using FX6, and may vary slightly between cameras.
- Connect either a USB-C cable between the camera and Bolt 7, or an Ethernet cable using a SmallHD 5-pin to RJ45 adapter. Note that cameras like FX6 require an adapter to use Ethernet, others have an RJ45 Ethernet jack built in
- Ethernet Connection
- Open the camera's full menu
- Navigate to Network > Wired LAN
- Ensure that Wired LAN is set to ON
- Ensure that Camera Remote Control is set to Enable
- USB-C Connection
- Open the camera's full menu
- Navigate to Network > USB Tethering
- Ensure USB Tethering is set to ON
- Ensure Camera Remote Control is set to Enable
- Refer back to the Network > Wired LAN menu to view the camera's network information
- Refer to the camera's manual for additional network configuration info
- Configure the Camera's Remote control password on the Network > Network Setup menu. You will need the password in order to connect
SmallHD Monitor Setup
Bolt 7 can be connected to your monitor with a 5-pin to USB-C cable, or with a 5-pin to Ethernet adapter. Note that a 5-pin to 5-pin USB cable cannot be used between Bolt 7 and the monitor as both ports operate in USB host mode.
After connecting the cable between Bolt 7 and the monitor you can configure the Camera Control function in the monitor.
- Open the monitor's settings menu
- Scroll down to Camera control
- Select the appropriate SONY camera control. If you don't see this menu option, you may need to purchase a camera control license. Please visit www.smallhd.com to purchase the license
- Enter the camera's LAN IP and CAP password
SmallHD has more info about Camera control in their reference guide: https://guide.smallhd.com/m/118985/c/418183
Supported Cameras
- BURANO
- FX5
- FX6
- VENICE
- VENICE 2
Additional Notes
- Ensure the camera and monitor are on the same subnet if using Client mode with another router.
- Some network settings may vary slightly by firmware version—always refer to the latest camera manuals for exact menu locations.
For additional guidance, see Sony's official documentation:
