The Bolt 6 LT TX (Japan) and RX set was built to meet Japan's MICA 6GHz requirements for certification. It is a real-time wireless video transmission system that supports 4K video with Teradek's patented Zero-Delay technology, now with less interference using the newly opened 6GHz wireless frequency. Bolt 6 LT can send and receive color-accurate, True-HDR videos in under 0.001 seconds using the set's included Bolt 6 LT video Transmitter and Receiver. Bolt 6 LT is cross-compatible with the entire Bolt 4K Series – including Bolt 4K, Bolt 4K LT, and the Bolt 4K Monitor Modules – giving you the option to expand your workflow requirements. Link up to 6 receivers to one transmitter.
Table of Contents
What's Included
- Bolt 6 LT Transmitter w/Internal Antenna and Receiver w/External Antenna
- Hot Shoe Adaptor
- Lightstand Adapter 1/4-20in
- (Bit 118) 2pin Conn. to PowerTap - 18in Cable
- (Bit 718) 2pin Conn. to 2pin Conn. (Alexa) 18in Cable
- SDI - BNC to BNC Cable, 10in
- USB Male Type A (Full) - USB Male Type B (Micro) -3ft Cable
- Ultra Thin HDMI Male Type A (Full) - HDMI Male Type A (Full) 18in Cable
- PSU 2pin Conn. to 18W AC Adapter (Int) - 6ft Cable
Power and Connect
- Connect your power source to the transmitter and receiver using the included A/C adapter. If both devices are equipped with battery plate accessories, attach a compatible battery (Gold or V mount).
- Connect the output from your video source to either the SDI or HDMI input (C or E) on the Bolt transmitter.
- Connect either the SDI or HDMI output (D or J) from the Bolt receiver to the video input on your monitor.
- Turn the units on by moving the power switches on both the transmitter and receiver (J) to the ON position.
Pairing/Unpairing
Bolt devices purchased as a set (TX and RX), are paired by default, requiring no additional configuration. Bolt devices purchased separately need to be paired using the device's front panel (OLED) menu, Bolt Manager, or the Bolt App. To pair your transmitter with multiple receivers, you will need to use either Bolt Manager or the Bolt App. NOTE: Before starting either pairing process, ensure that both the transmitter and receiver have the same firmware version and have Bluetooth enabled.
PAIRING/UNPAIRING VIA FRONT PANEL
Pair:
- Using the Menu Joystick, navigate to the Pair menu on both the transmitter and the receiver front panel.
- Select Pair to begin the pairing process. The transmitter will begin scanning for a receiver within range and automatically pair to the receiver.
- Once paired, the front panel will indicate whether or not Pairing is successful.
To Unpair:
- Navigate to the Unpair menu on either the transmitter and the receiver.
- Select the transmitter/receiver you want to unpair. If you have multiple devices paired, you can select Unpair All.
PAIRING TIPS
If you’re having trouble getting units to pair, we recommend keeping the transmitter and receiver six feet apart when pairing. Keep all other RF devices nearby turned off or out of range to ensure the transmitter and receiver are only detecting each other. To eliminate any chance of interference, perform the Wired Pairing process via Bolt Manager.
PAIRING VIA BOLT APP
Pair:
- Open the Bolt App from your iOS or Android device, then tap the Pairing button.
- Select the transmitter you wish to pair, then tap the Next button.
- Select the receiver(s) you wish to pair with the transmitter, then tap the Pair! button. The Bolt App will indicate when the pairing process is complete.
To Unpair:
- Open the Bolt App from your iOS or Android device, then tap the TX settings button (3 dots) on the top right corner of the screen.
- Enter the Pairing menu, select the receiver(s) you wish to unpair, then tap the Unpair button.
WIRED PAIRING VIA BOLT MANAGER
To Pair:
- Connect both the transmitter and receiver(s) to your computer (Windows/Mac) via USB.
- Open Bolt Manager, select the Pairing tab, then tap the Wired Pairing button.
- Select the devices you want to pair, then click the Pair Devices button. Bolt Manager will indicate whether or not Pairing is successful.
To Unpair:
- Connect the transmitter to your computer (Windows/Mac) via USB.
- Open Bolt Manager, select the Pairing tab, then tap the Unpair All button.
Power Cables
2-Pin Power Connector
Bolt devices use a locking 2-pin power connector similar to the 0B 302 series LEMO connector.
* Pin 1 is closest to the red dot on the connector.
Input Voltage: 6-28V DC
Max Power Consumption: 20W (TX) and 18W (RX)
Custom/3rd Party Cables
- Test the power cable polarity with ONLY the power cable connected to Bolt. Do not connect video cables.
- Check the power cable for shorts and proper grounding.
CAUTION:
Using a reverse polarity or improperly−constructed power cable can damage the product and is not covered under warranty. To prevent the inputs from being damaged, best practice is to plug in the power cable first, THEN connect the video cable from the camera before powering on the TX unit.
TX/RX Configuration Menus
Wireless Configuration
Switch TX (RX Only) - Bolt 6 receivers can pair with up to four transmitters at a time. Switch TX allows you to quickly switch from one paired transmitter's camera feed to another paired transmitter. This feature is especially useful in multi-camera situations when you need to switch to a different camera's view mid-shoot, without having to perform the pairing process every time. NOTE: The transmitter(s) need to first be paired with the receiver.
Band - Select either the 5GHz or 6GHz wireless frequency. The 5GHz frequency provides more channels but is utilized by more devices, resulting in frequent interferences and video dropouts. The 6GHz frequency is less crowded than the 5GHz frequency, resulting in faster connections and less interference. NOTE: The 6GHz band is intended for indoor use only
Enable Broadcast Mode (Bolt 6 LT MAX transmitters only) - Broadcast Mode allows you to transmit to multiple receivers simultaneously (non-DFS frequencies only), while also extending your Bolt 6's transmission range.
- Broadcast Mode Disabled (Standard Multicast Mode) - Transmitter and connected receiver(s) coordinate and maintain two-way communication with each other to optimize frequency usage and video transmission.
- Broadcast Mode Enabled - Data uplink channel is disabled, allowing the transmitter to connect to an unlimited number of receivers, as long as they have already been paired. To achieve even better range performance, attach the receiver to your Bolt Panel Antenna while in Broadcast Mode. NOTE: Bolt 6 LT 750 and 1500 receivers will not link to a Bolt 6 LT MAX transmitter in Broadcast Mode, even if they were previously paired. You must use a Bolt 6 LT MAX receiver. Otherwise, the transmitter's OLED will display Broadcast Not Supported.
Enable Fixed Frequency - Fixed Frequency Mode allows your transmitter to designate a specific non-DFS channel within the selected wireless region for use, providing a stronger connection in difficult environments. There are two options for Fixed Frequency Mode:
- Non-DFS and non-6GHz channels
- Specific non-DFS 5GHz channels
NOTE: By default, Bolt 6 LT will select the lowest available frequency from the Frequencies list if one has not been selected beforehand.
Bandwidth - Choose between 20MHz and 40MHz bandwidth options
Frequencies - Select which frequency to use (determined by Fixed Frequency Mode selection).
Video Quality - The Video Quality menu lets you adjust the balance between your signal’s maximum range and quality according to the number of antennas used to transmit fine information. Bolt 6 LT has three picture quality levels that vary based on the lowest quality link or the furthest receiver.
- Auto Mode - (Default) Transmitter automatically determines how many fine antennas are needed based on the range and signal quality.
- Longer Distance Mode - (One fine antenna) Maintains the maximum range in situations where other sources of interference might be present, but will slightly reduce your video signal’s maximum quality.
- Better Quality Mode - (Two fine antennas) Maintains higher signal quality but reduces the maximum range.
Video Settings
3D LUT Settings (RX Only) - The 3D LUT settings menu contains specific looks that can be applied to your video output that either match or simulate how the video will appear after editing, along with options for how they are overlayed on your video output (Full or Split-screen).
- 3D LUT Presets - Select a specific look from the list of 3D LUT presets.
-
3D LUT Mode - Select whether the look is applied to the entire video output (Full Screen) or
half (Split Screen).
Video OSD Settings (RX Only) - Choose when to display the OSD.
- Never show
- Show when operating
- Show when no video
- Always show
Display Settings - Use the Display Settings to control the OLED display operation. By default, the OLED display will invert every 30 minutes.
Tools
Signal Quality Graph (RX Only) - The Signal Quality Graph indicates the quality and reliability of the signal being received according to the amount of interference that is present between the RX and TX. Signal Quality is represented in percentages:
- Figures below 30% indicate poor signal quality
- Figures between 30% and 45% indicate fair signal quality
- Figures above 45% indicate good signal quality
Spectrum Analyzer (RX Only) - The built-in Spectrum Analyzer provides a visual indication of channel noise and saturation across the entire available frequency range. Move the Menu joystick left and right to select a frequency. Frequencies are represented by bars; the higher the bar, the more congested that frequency is.
Test Pattern (RX Only) - This menu allows you to select a video resolution format to output a test pattern over HDMI or SDI. Select a specific output resolution from the resolutions list.
Advanced/System Settings
Lock Keypad - The Lock Keypad feature prevents the menu joystick from being used to avoid any accidental or unauthorized configurations. There are two ways to lock the keypad:
- Navigate to Advanced Settings via the front panel and select Lock Keypad.
- Press and hold the menu joystick upward for 5 seconds.
To unlock, press and hold the menu joystick upwards for five seconds or until the display reads "KEYPAD UNLOCKED."
HDMI (RX only) - Bolt 6 supports all HDMI output modes. You can select from one of the following options:
- Auto
- RGB 8bit
- RGB 10bit
- YCbCR 4:4:4 8bit
- YCbCR 4:4:4 10bit
- YCbCR 4:2:2 10bit
- YCbCR 4:2:0 8bit
- YCbCR 4:2:0 10bit
Audio (RX only) - Configure Bolt’s Audio settings. If Beep on REC is activated, you will hear a short tone whenever the camera begins or stops recording. The Mute Settings allow you to completely mute audio or only mute audio while recording.
Bluetooth - Use the Bluetooth menu to enable or disable Bluetooth communication. NOTE: Bluetooth is enabled by default.
- Enable Bluetooth - Allows transmitter and receiver to be paired and communicate with the Bolt App.
- Use Bluetooth PIN - Enables the use of a PIN for authentication when using the Bolt App.
- Change PIN - Press the Menu joystick towards the right to change the Bluetooth PIN
Background Color (RX only)- The Background Color feature allows you to select a screen color to be displayed on the monitor when there is no video being received from the transmitter. This is a useful tool that indicates to the crew that a signal has been dropped and the TX and RX need to be synced again.
Reset All Settings - Reset all configurable options to their factory settings.
Additional Information
Device Info - Displays the model and serial number of the device
Firmware Versions - Displays the current firmware versions for all device components.
Regulatory - Displays all compliance certifications and certification markings related to radio frequencies used by the TX and RX to communicate. For complete regulatory information and declarations of conformity, please visit the Regulatory Information section.
Bolt App
Use the Bolt App to remotely manage and monitor every parameter of Bolt 6 including pairing, frequency selection, and 3D LUTs.
CONNECT VIA BLUETOOTH
- Download the Bolt App.
- Enable Bluetooth on your iOS or Android device.
- Navigate to the Bluetooth menu on both the transmitter and receiver, then select Enable.
- Open the Bolt App from your iOS or Android device, then tap the Bolt Devices button.
- Select the device(s) you want to pair or monitor.
Transmitter Status Display
- Settings (Descriptions listed in Transmitter Menu section) - Tap the settings button on the top right corner of the screen to customize the transmitter’s various settings.
- Status - Displays the current status of:
- Video Input
- Network Status
- Connected Receivers
- Current Frequency
- Quality
- Temperature
- Camera Recording
- Region
- Bandwidth
- OSD name
Receiver Status Display
- Settings (Descriptions listed in Receiver Menu section) - Tap the settings button on the top-right corner of the display to customize the receiver’s various settings such as the output format, audio, display, and OSD.
- Signal Quality - Determine the quality and reliability of the signal being received.
- SNR (Signal to Noise Ratio) - Compare the signal power level to the noise power level from the antennas.
- Range Analyzer - Displays the transmission distance between the transmitter and receiver.
- Status - Displays the current status of:
- TX Name
- Network Status
- Link
- Video Input
- Current Frequency
- Range
- Quality
- Temperature
- Camera Recording
- Bandwidth
- Region
- OSD name
Other Resources
- USER MANUAL: https://guide.teradek.com/m/112641
- FIRMWARE UPGRADE: https://teradek.com/pages/downloads#bolt6