Ranger 4K is a zero-delay (< 1 ms) wireless video system that transmits uncompressed 4K HDR video up to 5,000 ft. line of sight. With best-in-class performance in challenging RF conditions and a wide operating range from 4.9 GHz to 6.0 GHz, Ranger offers live productions the ultimate combination of industry-leading video quality and wireless integrity.
Table of Contents
What's Included
- Ranger 4K Transmitter and Receiver
- Lightstand Adapter 1/4-20in
- (Bit 118) 2pin Conn. to PowerTap - 18in Cable
- Ultra Thin HDMI Male Type A (Full) - HDMI Male Type A (Full) 18in Cable
- SDI 12G BNC to BNC Cable Length: 18in / 46cm
- USB 2.0 Type A Male to USB Type B (Micro) Male - 1m Cable
- PSU 2pin Conn. to 30W AC Adapter (Int) - 6ft Cable
- 1x N-Type Barrel H Antenna
- 1x N-Type Barrel V Antenna
- 3x 2dBi WIFI 2.4/5.8GHz Antennas
- 2x 2dBi Flexible H Mushroom V4.9-7.3Ghz RP-SMA
- 5x RP-SMA Female to RP-SMA Female 4in/10cm Cable
Physical Properties
Power and Connect
- Attach the Ranger transmitter (male side) to the back of your camera.
- Connect power to the Ranger transmitter and receiver with the included A/C adapter, or if both devices are equipped with battery plate accessories, attach a compatible battery (Gold or V mount).
- Connect the output from your video source to either the SDI or HDMI input (D or E) on the Ranger transmitter. Connect either the SDI or HDMI output (E or M) from the Ranger receiver to the video input on your monitor. NOTE: If mounting the receiver upright on a stand above the monitor, use a right-angle SDI adapter to relieve any strain caused by the weight of the cable, and to avoid damaging the SDI output’s internal connectors.
-
Transmitter: Attach the H and V barrel antennas to the type-N connectors on the transmitter (A, B). The V antenna attaches to the V-connector, and the H antenna attaches to the H-connector.
Receiver: Attach the three 2dBi antennas to the receiver’s center connectors and the two horizontal antennas to the left and right connectors. - Move the power switches on both the transmitter and receiver (L) to the ON position. Video appears within a few seconds.
Pairing/Unpairing
Ranger devices purchased as a set (TX and RX), are paired by default, requiring no additional configuration. Ranger devices purchased separately need to be paired using the device's front panel (OLED) menu, Ranger Manager, or the Ranger App. To pair your transmitter with multiple receivers, you will need to use either Ranger Manager or the Ranger App. NOTE: Before starting either pairing process, ensure that both the transmitter and receiver have the same firmware version and have Bluetooth enabled.
PAIRING/UNPAIRING VIA FRONT PANEL
To Piar:
- Using the Menu Joystick, navigate to the Pair menu on both the transmitter and the receiver front panel.
- Select Pair to begin the pairing process. The transmitter will begin scanning for a receiver within range and automatically pair to the receiver.
- Once paired, the front panel will indicate whether or not Pairing is successful.
To Unpair:
- Navigate to the Unpair menu on either the transmitter and the receiver.
- Select the transmitter/receiver you want to unpair. If you have multiple devices paired, you can select Unpair All.
PAIRING TIPS
If you’re having trouble getting units to pair, we recommend keeping the transmitter and receiver six feet apart when pairing. Keep all other RF devices nearby turned off or out of range to ensure the transmitter and receiver only detect each other. To eliminate any chance of interference, perform the Wired Pairing process via the Ranger app.
WIRED PAIRING VIA RANGER MANAGER
To Pair:
- Connect the transmitter and receiver(s) to your computer (Windows/Mac) via USB.
- Open Ranger Manager, select the Pairing tab, then tap the Wired Pairing button.
- Select the devices you want to pair, then click the Pair Devices button. Ranger Manager will indicate whether or not Pairing is successful.
To Unpair:
- Connect the transmitter and receiver(s) to your computer (Windows/Mac) via USB.
- Open Ranger Manager, select the Pairing tab, then tap the Unpair All button.
PAIRING VIA RANGER APP
To Pair:
- Open the Ranger App from your iOS or Android device, then tap the Pairing button.
- Select the transmitter you wish to pair, then tap the Next button.
- Select the receiver(s) you wish to pair with the transmitter, then tap the Pair! button. The Ranger App will indicate when the pairing process is complete.
To Unpair:
- Open the RangerApp from your iOS or Android device, then tap the settings button (3 dots) on the top right corner of the screen.
- Enter the Pairing menu, select the receiver(s) you wish to unpair, then tap the Unpair button.
Power Cables
2-Pin Power Connector
Ranger devices use a locking 2-pin power connector similar to the 0B 302 series LEMO connector.
* Pin 1 is closest to the red dot on the connector.
Input Voltage: 7-28V DC (TX) and 6-28V DC (RX)
Max Power Consumption: 19W (TX) and 15W (RX)
Custom/3rd Party Cables
- Test the power cable polarity with ONLY the power cable connected to Ranger. Do not connect video cables.
- Check the power cable for shorts and proper grounding.
12G-SDI Input/Output Cables
Ranger units require the use of 12G-SDI cables to reliably transport 12G video signals and are included as a standard item. Ensure that your cables are rated for compatibility with your camera's output.
CAUTION:
Using a reverse polarity or improperly−constructed power cable can damage the product and is not covered under warranty. To prevent the inputs from being damaged, best practice is to plug in the power cable first, THEN connect the video cable from the camera before powering on the TX unit.
Mounting
Ranger devices have a 1/4”-20 threaded hole (additional 3/8”-16 threaded hole on the receiver) on the bottom for mounting the included light stand adapter or any other mounting accessory. Additionally, Ranger devices are equipped with a dual-mount battery plate that allows you to attach your device to either the back of a camera, monitor, or Array Antenna.
- Mount the transmitter onto the back of your camera keeping the antennas clear of any obstructions.
- Orient the transmitter and receiver antennas so they are parallel to each other.
- For best results, orient the transmitter antennas so each one has clear line-of-sight to the receiver.
CAUTION: DO NOT OVERTIGHTEN SCREWS INSERTED INTO THE THREADED HOLES. Doing so can damage the device's chassis and internal components, voiding the warranty.
TX/RX Configuration Menus
Wireless Settings
Switch TX (RX Only) - Ranger receivers can pair with up to four transmitters simultaneously. Switch TX allows you to quickly switch from one paired transmitter's camera feed to another paired transmitter. This feature is handy in multi-camera situations when you need to switch to a different camera's view mid-shoot without having to perform the pairing process every time. NOTE: The transmitter(s) must first be paired with the receiver.
Enable Broadcast Mode (TX Only)- Broadcast Mode allows you to transmit to multiple receivers simultaneously (non-DFS frequencies only) while extending your Ranger's transmission range.
- Broadcast Mode Disabled (Standard Multicast Mode) - Transmitter and connected receiver(s) coordinate and maintain two-way communication to optimize frequency usage and video transmission.
- Broadcast Mode Enabled - Data uplink channel is disabled, allowing the transmitter to connect to an unlimited number of receivers, as long as they have already been paired. Attach the receiver to your Panel Antenna while in Broadcast Mode to achieve even better range performance.
Enable Fixed Frequency - Fixed Frequency Mode allows your transmitter to designate a specific non-DFS channel within the selected wireless region for use, providing a stronger connection under challenging environments. NOTE: By default, Ranger will select the lowest available frequency from the Frequencies list if one has yet to be selected beforehand.
Allow Licensed Channels - Enable or disable Licensed Channel selection within the Frequencies menu. Ranger supports an extended RF range of 4.9GHz to 6.0GHz, which includes both unlicensed and licensed channels. Selecting a specific licensed channel ensures no interference from other devices broadcasting within range. NOTE: Fixed Frequency Mode must first be enabled to select a specific licensed channel. Otherwise, Ranger will automatically select a licensed channel (Auto Mode).
Bandwidth - Choose between 20MHz and 40MHz bandwidth options
Frequencies - Select which frequency to use (determined by Fixed Frequency Mode selection).
Video Quality - The Video Quality menu lets you adjust the balance between your signal’s maximum range and quality according to the number of antennas that transmit fine information. Ranger has several picture quality levels that vary based on the lowest quality link or the furthest receiver.
- Auto Mode - (Default) Transmitter automatically determines how many fine antennas are needed based on the range and signal quality.
- Longer Distance Mode - (One fine antenna) Maintains the maximum range in situations where other sources of interference might be present but will slightly reduce your video signal’s maximum quality.
- Better Quality Mode - (Two fine antennas) Maintains higher signal quality, but reduces the maximum range.
- Best Quality Mode - (Three fine antennas) Ideal for complex, high-contrast scenes that require the highest possible quality.
- Low Power Mode - (One fine antenna with shorter range) Reduces the transmitter's total power consumption by about 1.5W, and may reduce any unwanted interference in multi-system environments.
Video Settings
HDMI/SDI Output Format (RX only) - Select the video output format. You can match the video source’s resolution (Same As Input) or choose from the resolutions listed. If using the receiver with a recorder or monitor sensitive to video signal changes, select Continuous Output to ensure the signal stays constant even if the link is interrupted. Note that this adds a small delay to the video output.
Video OSD Settings (RX Only) - Choose when to display the OSD.
- Never show - Disable OSD.
- Show when operating - Hide OSD until it is activated by the joystick.
- Show when no video - Display the OSD when there is no video feed; hide the OSD when video appears (default).
- Always show - Always display OSD unless temporarily deactivated by the joystick.
Display Settings - Use the Display Settings to control the OLED display operation. By default, the OLED display will invert every 30 minutes.
Tools
SDI Eye Pattern (TX only) - The SDI Eye Pattern provides a graphical display of the SDI signal coming from the camera to the transmitter, and is useful in determining the amount of interference present. The size of the "eye" displayed on the front panel indicates the quality of the SDI signal. The bigger the size of the eye pattern is, the better the SDI signal.
Signal Quality Graph (RX Only) - The Signal Quality Graph indicates the quality and reliability of the signal being received according to the amount of interference that is present between the RX and TX. Signal Quality is represented in percentages:
- Figures below 30% indicate poor signal quality
- Figures between 30% and 45% indicate fair signal quality
- Figures above 45% indicate good signal quality
Spectrum Analyzer (RX Only) - The built-in Spectrum Analyzer provides a visual indication of channel noise and saturation across the entire available frequency range. Move the Menu joystick left and right to select a frequency. Frequencies are represented by bars; the higher the bar, the more congested that frequency is.
Test Pattern (RX Only) - This menu allows you to select a video resolution format to output a test pattern over HDMI or SDI. Select a specific output resolution from the resolutions list.
Advanced/System Settings
Lock Keypad - The Lock Keypad feature prevents the menu joystick from being used to avoid any accidental or unauthorized configurations. There are two ways to lock the keypad:
- Navigate to Advanced Settings via the front panel and select Lock Keypad.
- Press and hold the menu joystick upward for 5 seconds.
To unlock, press and hold the menu joystick upwards for five seconds or until the display reads "KEYPAD UNLOCKED."
HDMI (RX only) - Ranger supports all HDMI output modes. You can select from one of the following options:
- Auto
- RGB 8bit
- RGB 10bit
- YCbCR 4:4:4 8bit
- YCbCR 4:4:4 10bit
- YCbCR 4:2:2 10bit
- YCbCR 4:2:0 8bit
- YCbCR 4:2:0 10bit
Audio (RX only) - Configure Ranger’s Audio settings. If Beep on REC is activated, you will hear a short tone whenever the camera begins or stops recording. The Mute Settings allow you to completely mute the audio or only mute audio while recording.
Bluetooth - Use the Bluetooth menu to enable or disable Bluetooth communication. NOTE: Bluetooth is enabled by default.
- Enable Bluetooth - Allows transmitter and receiver to be paired and communicate with the Ranger App.
- Use Bluetooth PIN - Enables the use of a PIN for authentication when using the Ranger App.
- Change PIN - Press the Menu joystick towards the right to change the Bluetooth PIN
Background Color (RX only)- The Background Color feature allows you to select a screen color displayed on the monitor when no video is received from the transmitter. This valuable tool indicates to the crew that a signal has been dropped and the TX and RX need to be synced again.
Reset All Settings - Reset all configurable options to their factory settings.
Additional Information
Device Info - Displays the model and serial number of the device
Firmware Versions - Displays the current firmware versions for all device components.
Regulatory - Displays all compliance certifications and certification markings related to radio frequencies used by the TX and RX to communicate. For complete regulatory information and declarations of conformity, please visit the Regulatory Information section.
Ranger App
Use the Ranger App to remotely manage and monitor every parameter of Ranger, including pairing, frequency selection, and 3D LUTs.
CONNECT VIA BLUETOOTH
- Download the Lan App.
- Enable Bluetooth on your iOS or Android device.
- Navigate to the Bluetooth menu on both the transmitter and receiver, then select Enable.
- Open the Ranger App from your iOS or Android device, then tap the Status/Configuration button.
- Select the device(s) you want to pair or monitor.
Transmitter Status Display
- Settings (Descriptions listed in TX/RX Configuration Menus section) - Tap the settings button on the top right corner of the screen to customize the transmitter’s settings.
- Status - Displays the current status of:
- Video Input
- Network Status
- Connected Receivers
- Current Frequency
- Quality
- Temperature
- Camera Recording
- Region
- Bandwidth
- OSD name
Receiver Status Display
- Settings (Descriptions listed in TX/RX Configuration Menus section) - Tap the settings button on the top-right corner of the display to customize the receiver’s various settings, such as the output format, audio, display, and OSD.
- Signal Quality - Determine the quality and reliability of the received signal.
- SNR (Signal to Noise Ratio) - Compare the signal power level to the noise power level from the antennas.
- Range Analyzer - Displays the transmission distance between the transmitter and receiver.
- Spectrum Analyzer - Visually indicates channel noise and saturation across the available frequency range.
- Status - Displays the current status of:
- TX Name
- Network Status
- Link
- Video Input
- Current Frequency
- Range
- Quality
- Temperature
- Camera Recording
- Bandwidth
- Region
- Video Output
- OSD name
Other Resources
- USER MANUAL: https://guide.teradek.com/m/112641
- FIRMWARE UPGRADE: https://teradek.com/pages/ranger