Recent updates
-
Panel Antenna v.4
Updated onArticlesOMNIDIRECTIONAL ANTENNA
The included omni-directional antenna (A) can receive a signal from your transmitter even when it’s placed behind the Panel Antenna, and supports a wider spectrum (4.9-7.3 GHz).Wireless Video Ranger Physical Properties
-
Regulatory Information
Updated onArticlesPRODUCT INFORMATION
This product is designed to be compliant with rules and regulations in the country it is sold to and therefore is marked as required. These markings signify the countries the device is approved in. Operating the product without regulatory approval is illegal. Any changes or modifications to the product not expressly approved by Teradek could void the user's authority to operate the equipment and its regulatory approvals. Please make sure you use the latest revision of this document which is available at teradek.com.SAFETY INSTRUCTIONS
- Keep these instructions in a safe and accessible place for future use.
- When operating this equipment, read and follow all the instructions in this manual.
- Do not open the unit.
- Do not block the air ventilation openings, and provide proper ventilation for the units to allow them to cool down during operation.
- Use only accessories/batteries/chargers specified or recommended by Teradek.
- When devices are switched ON, keep away at least 20 cm (7.9 in) from your body.
- People with pacemakers should ALWAYS keep the device at the listed distance from their pacemaker when turned ON. Should you have any reason to suspect that interference is taking place, you should turn your device OFF.
- Do not expose to moisture, excessive heat, or fire.
- Keep away from water and other liquids.
- Clean with a dry cloth only.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- To reduce the risk of fire or electric shock, refer servicing to qualified service personnel.
Declared maximum operating temperature: +40°C - Please avoid electrostatic discharge from the antenna ports for proper operation
WARNING
Ranger devices contain sensitive electronic components that can be damaged by electrostatic discharge (ESD). When handling, care must be taken so that the device is not damaged. Damage due to inappropriate handling is not covered by the warranty. For complete warranty information, please see the warranty card that arrived with the device, or visit www.teradek.com/pages/warranty-information.USING THE AC POWER ADAPTOR
- All components must be dry before connecting to an external power source
- Use ONLY a UL/IEC 62368 or UL/IEC 60950-1 2nd revision approved AC/DC power adapter class LPS with an electrical output rating range of 6-28 V DC, 3A, with an ambient temperature range of 0°C to 40°C.
- Use of an alternative AC/DC power adapter will invalidate any approvals given to this unit and may be dangerous.
BATTERY
This device is not supplied with batteries. In case a battery is used, please adhere to the following general battery usage guidelines:- Use batteries with the rated voltage and current characteristics as listed in the manual.
- Use IEC 62133-approved lithium batteries such as the Anton Bauer Digital Battery (Dionic XT 150/Dionic XT 90).
- Verify battery temperature is within the range specified.
- Do not use incompatible/incorrect batteries. Use of an incompatible battery may present a risk of fire, explosion, leakage, or other hazards.
- Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
RF MODULES
These devices contain the following approved radio modules:Wireless Video Ranger Additional Information
-
Device Placement
Updated onArticlesRanger devices are equipped with a dual-mount battery plate that allows you to attach your device to either the back of a camera, monitor, or Bolt Panel Antenna.
Wireless Video Ranger Mounting
-
Antenna Orientation
Updated onArticlesRanger units require the use of external antennas for basic operation. For Ranger, we recommend ONLY using a Horizontal + Vertical (H+V) antenna configuration.
Wireless Video Ranger Mounting
-
Launchpad App
Updated onArticlesUse the Launchpad App to remotely manage and monitor every parameter of Ranger including pairing, and frequency selection.
Wireless Video Ranger Launchpad App
-
Device Operation
Updated onArticles- Keep the transmitter and receiver at close range for 60 seconds after powering on the devices. This allows them to scan for and select the best wireless frequency.
- For best results when using multiple Ranger systems in the same area, place the transmitters and receivers a few feet apart from each other.
- Operation of other wireless equipment may interfere with the Ranger. Try to separate other wireless transmitters and receivers as much as possible.
Wireless Video Ranger Getting Started
-
Power and Connect
Updated onArticles- Attach the Ranger transmitter (male side) to the back of your camera.
- Connect power to the Ranger transmitter and receiver with the included A/C adapter, or if both devices are equipped with battery plate accessories, attach a compatible battery (Gold or V mount).
- Connect the output from your video source to either the SDI or HDMI input (D or E) on the Ranger transmitter. Connect either the SDI or HDMI output (E or M) from the Ranger receiver to the video input on your monitor. NOTE: If mounting the receiver upright on a stand above the monitor, use a right-angle SDI adapter to relieve any strain caused by the weight of the cable, and to avoid damaging the SDI output’s internal connectors.
-
Transmitter: Attach the H and V barrel antennas to the type-N connectors on the transmitter (A, B). The V antenna attaches to the V-connector, and the H antenna attaches to the H-connector. Receiver: Attach the three 2dBi antennas to the receiver’s center connectors and the two horizontal antennas to the left and right connectors.
If using a Panel Antenna with the receiver: Connect the receiver’s three center connectors to the Array Antenna connections labeled “V,” then connect the left and right connectors to the “H” connections using the RP-SMA connectors (see MOUNTING). NOTE: Ensure that the 2dBi omnidirectional antenna (A) is attached at all times to the Panel Antenna when in use. - Move the power switches on both the transmitter and receiver (J) to the ON position. Video appears within a few seconds.
Wireless Video Ranger Getting Started
-
Launchpad
Updated onArticlesWith Launchpad, you can configure all of your Ranger devices at once. Available as software for Windows and Mac, Launchpad allows you to pair multiple receivers to your transmitter, select frequencies, and perform firmware upgrades.
Wireless Video Ranger Configuration
-
Info
Updated onArticlesDEVICE INFO
Reset all configurable options to their factory defaults.FIRMWARE VERSIONS
Displays the current firmware versions for all device components.REGULATORY
Displays all compliance certifications relating to radio frequencies used by the TX and RX to communicate.
For complete regulatory information and declarations of conformity, please visit the Regulatory Information section.Wireless Video Ranger Configuration
-
Advanced Settings
Updated onArticlesLOCK KEYPAD
Enabling the Lock Keypad feature prevents the menu joystick from being used to avoid any accidental or unauthorized configurations. There are two ways to lock the keypad:- Navigate to Advanced Settings via the front panel and select Lock Keypad.
- Press and hold the menu joystick upward for 5 seconds.
To unlock, press and hold the menu joystick upwards for five seconds or until the display reads "KEYPAD UNLOCKED."
HDMI (RX only)
Ranger supports all HDMI output modes. You can select from one of the following options:- Auto
- RGB 8bit
- RGB 10bit
- YCbCr 4:4:4 8bit
- YCbCr 4:4:4 10bit
- YCbCr 4:2:2 10bit
- YCbCr 4:2:0 8bit
- YCbCr 4:2:0 10bit
AUDIO (RX only)
Configure Ranger’s Audio settings. If Beep on REC is activated, you will hear a short tone whenever the camera begins or stops recording. The Mute Settings allow you to completely mute the audio or only mute audio while recording.- Beep on REC - Short tone when the camera begins or stops recording
-
Mute Settings- Select an option:
- Off
- Mute while recording
- On
BLUETOOTH
Use the Bluetooth menu to enable or disable Bluetooth communication.- Enable Bluetooth - Allows transmitter and receiver to be paired and communicate with the Launchpad App.
- Use Bluetooth PIN - Enables the use of a PIN for authentication when using the Launchpad App.
- Change PIN - Press the Menu joystick towards the right to change the Bluetooth PIN
NOTE: Bluetooth is disabled by default. To configure your Ranger devices via the Launchpad App, you must first enable Bluetooth.
BACKGROUND COLOR (RX only)
The Background Color feature allows you to select a screen color to be displayed on the monitor when there is no video being received from the transmitter. This is a useful tool that indicates to the crew that a signal has been dropped and the TX and RX need to be synced again.RESET ALL SETTINGS
Reset all configurable options to their factory settings.Wireless Video Ranger Configuration